Two Reasons You Need a Shed Roof Overhang Apex roof shed. If you have ordered an apex shed, follow these steps: (for pent sheds, skip to step 33) Gable Tops. Line up the gable tops with the panels at the gable ends (the ends where you attached the �heavy duty bearers�). Secure them to the wall panels with 50mm screws from the inside, screwing upwards through the framing Missing: instagram. Roof Shape (Apex/Pent) Cabin Dimensions (Height, Width, Length, Overhang) Floor Thickness (20mm or 28mm) Wall Thickness (34mm, 44mm or 48mm) Veranda or Side Overhang. Walls (Partition) Windows (double glazed, tilt and turn) Doors (double glazed). The ideal shed roof overhang depends on the purpose of the overhang, the location and microclimate of the building. An overhang to protect the shed user on a rainy night could be relatively small whereas an overhang to provide a shaded area in front of the shed to keep the interior of the shed Missing: instagram.

If you start by joining the batons to the roof panels with 50mm screws as per the diagram below, and then place the roof panels in position the roof panels are universal so can go on either side. Start at one end placing a roof panel at each side and screw the roof panels together internally using 70mm screws. You can then work down the roof adding and joining roof panels to the baton on the adjoining roof panels with 50mm screws and joining the roof panels to each other with 70mm screws until all the roof panels are on.

There should be 6x screws joining the roof panels together every 4ft. Ensure the roof panel overhang at each end of the shed is even � there should be an approx.

Then, screw the roof panels to the side wall panels with 50mm screws ensuring you screw down in to every upright piece of framing on the side walls and screw the roof panels into the gables at each end with 35mm screws 4x screws for each gable. The roof now needs attaching to the trusses if there are trusses. To do this, screw down through the roof panels and into the truss from the outside with 35mm screws ensuring there are 8 screws per truss 4x on each side.

Roll out the mineral roofing felt along the lower part of Sheds With Front Overhang In one side of the roof. Allow for sufficient overhang to fold down onto the roof framing but not the underside of the roof.

Use clout nails to tack along the top edge of the felt and into the roof boards. Repeat this process on the other side of the roof.

This can be secured to the roof using clout nails. If you have an 8ft wide shed, you will receive another length of felt as well. Fold the overhanging felt at the gable ends under the roof boards and tack into place. Add the pent front top to the side you want to be higher and screw to the panels below with 50mm screws.

Depending on the size building you have ordered, your roof panels will be 2ft, 3ft, or 4ft wide. Place the roof panels in place so that the framing on the roof panel runs parallel with the gables i. Make sure the framing on the roof is in line with the framing on the gable top so that the overhang on the front and back is correct. Join the roof panels to each other and to the gables using 50mm screws, going through the framing from the inside of the building.

Then, screw the roof panels to the side wall panels with 50mm screws ensuring you screw up through the framing from the inside of the building into the framing on the roof panels. Before laying the felt, you will need to attach the back bargeboards with the 40mm galvanised nails.

As you can see there are two for the back � one at the edge of the roof and one on the underside. These soffits may come in more than one section and may need cutting down to size with a saw depending on which size shed you have chosen. Be sure not to mix these up with the corner strips and cover lats which are to go vertically around the shed in corners and covering joins explained later.

Allow for sufficient overhang to fold down onto the roof bargeboard but not the underside roof Sheds With Side Overhang Kit bargeboard. Use clout nails to tack along the top edge of the felt and into the roof board and the bottom edge of the felt into the back bargeboard. Fold down the overhanging felt on the gable ends and tack this into place.

Front and side bargeboards will cover any untidy edges. Using the 40mm galvanised nails, fit the bargeboards to the foot and sides of the roof. Again, these may need cutting down with a saw depending on what size building you have. Secure corner strips at each corner of your Power shed with 40mm nails at least four per strip.

Extra strips are provided to cover any joins between side wall panels. Return to all questions You do receive written instructions with your Power Shed. Shed base information: All of our garden sheds require a firm and level base. When thinking about where the garden building and base is going to be constructed: Ensure that there will be access to all sides for maintenance work and annual treatment. Remember not to place the base too close to any walls or fences, as there may be a slight overhang on the roof of the garden building which may come into contact with the wall or fence.

Ensure the base is level and is built on firm ground, to prevent distortion. Refer to PowerSheds. Consider when placing the base next to trees or large bushes as this could cause problems from overhanging branches, especially if these are likely to grow and come into contact with the building in the future and could cause the felt to rip.

Fixing pack: Your fixing pack will include: 25mm screws silver 35mm screws 50mm screws 70mm screws Clout nails for the felt 40mm galvanised nails 4. Shed floor assembly 6. Shed door assembly 8. Shed wall panel assembly Please ensure you have removed the transport blocks.

Continue doing this to place all remaining wall panels in position. Apex roof shed If you have ordered an apex shed, follow these steps: for pent sheds, skip to step 33 Gable Tops Trusses Apex roof panels Then, screw the roof panels to the side wall panels with 50mm screws ensuring you screw down in to every upright piece of framing on the side walls and screw the roof panels into the gables at each end with 35mm screws 4x screws for each gable Apex shed felt For finishing touches see step Pent roof shed If you have ordered a pent shed, follow these steps: Front pent top and gables Pent roof panels Felt Repeat this process along the higher part of the roof.

Even wind driven rain finds it difficult to enter a shed when protected by a relatively small overhang. At the bottom of the shed wall the fact that water from the roof is being directed away from the shed means that the base of the shed gets less persistently damp. When added to the use of a gutter to collect roof water the damage to the shed walls is minimised.

Even a relatively small overhang can provide significant protection Appearance In addition to the practical considerations designing a roof overhang into your shed helps to provide contrast and a sense of depth to the appearance of the building.

These aspects are hard to quantify but when you look at cheap sheds they often seem to look 'flat' and don't have much character. Once you start looking it is something that you can't 'un-see'. Having a well-proportioned roof overhang definitely gives a building more of a quality appearance. The relatively large eaves on this building and guttering system mean that the base of the shed rarely gets wet. Prolonging the life of the building.

What is the ideal shed roof overhang? The ideal shed roof overhang depends on the purpose of the overhang, the location and microclimate of the building. An overhang to protect the shed user on a rainy night could be relatively small whereas an overhang to provide a shaded area in front of the shed to keep the interior of the shed cool will be much larger.

This shed has a large overhang to the front to provide shading and protection from the rain With respect to providing protection from the rain for buildings with an 8ft eaves height then a mm eaves projection is about right. It also means that splashes from water dripping off the roof falls further from the building and so dampens the base of the shed less.

Having a guttering system reduces this effect most. An alternative is to use a gravel strip around the base of the shed so that any rain falling from the edge of the roof is dispersed rather than bouncing off a hard surface or from a puddle.

Forming a roof overhang is different dependant on the style of roof and also on which edge of the roof is being considered. Let's have a look at two different popular roof styles. On the other edge a 'gable ladder' is constructed which is formed from two rafters with 'noggins' between that support the end rafter. The noggins extend back for a series of three rafters. The roof overhang occurs in a similar way to the pent roof in that the top chord of the roof truss projects past the wall plate by the desired amount.

The overhang at the bottom of the slope is a simple overhang. Whereas the overhang on the gable end is a 'gable ladder' In the opposing direction a gable ladder is formed in a very similar way to the pent roof. The roof trusses don't extend out beyond the wall line.

Just the top chord of the roof with the noggins going back into the roof a distance of three rafters. One obvious reason is simplicity and economy. If you are making sheds to compete at as low a price-point as possible then you will want to cut out as many elements as possible. Many consumers don't realise the benefits of a good shed overhang and so are distracted by the low price. Not realising that this 'false economy' will come back to haunt them in a reduced lifespan of the shed that they are buying.

Also they will get reduced utility out of the shed from the shading and sheltering provided by a well-designed overhang. Alternatively if I was to put on my tin foil hat.




Grey Shed Instagram Post
Cost To Build A Shed 10x12 Nova